Blogger down - lost post - bangle problems

I guess many of you bloggers know that blogger has been down for a while (since last night for me in the UK). It made me realise that I have no other record of the information in my blog as I wanted to check back on my - things I want to make post to remind me and couldn't access it. Can you back up blogs? Must investigate.

Also I wrote a long wordy post on bangle problems - blogger has probably chosen not to publish it cause it was too long and boring! I will try and summarise it this time round.

I have trouble making solid polymer clay bangles, the often seem to break easily. At first they seemed to break at the join so I now add a bit of polypaste and make sure I smooth the seams carefully. That solved the popping at the seams but now means they break elsewhere instead! See evidence below

 These were made from very well conditioned Kato scrap clay extruded through the largest makins D shape die (about 8mm wide and about 5mm at it's thickest). Joined carefully with some polypaste, baked on an empty coke can at 150 oC (300F) for 40 mins. They broke when I was carefully sliding them from the coke can, the first break was not at the join. Glad they broke then rather than after I had taken the time to cover them  I suppose!

This bangle is made from a sausage of well conditioned Kato clay joined carefully with some polypaste in the join, covered with a decorated sheet of cane slices, baked on an empty coke can at 150oC for 1 hour. It looked fine and felt strong so I wore it for a morning. All good until I decided to sand it. Almost the minute I started gently sanding with my soft micromesh cloth draped over my fingers it broke. It is quite skinny, about 8mm in diameter, like some others I have been wearing which are fine - here's a post about them.

So where am I going wrong with them? My husband has a feeling that baking them for a long time they are strong but brittle and I should under cure them rather than cure them for longer so they are more ductile, less brittle. I was about to start some baking trials for different times when I came across a post from Tony Aquino on the Kato Polyclay Facebook page stating that the higher the cure temperature the stronger the clay will be. I will try and test some different temperatures too. What I need for bangles is something with a little flex I guess. I've had a few suggestions from clever people at the PCC Forum to try out. I will report back with anything I find out, but please leave a comment or mail me if you have any ideas I could try to make bangles that don't break!

thanks

Cara

Purple Flowers,pendants, micromesh and pens

My mum got more birthday presents made by me. I wasn't quite sure how my disc necklace would work out so I went back to something I knew would work just in case - a flowery cabochon. Again in purples. It turned out very well, I'm very pleased with it. She ended up with both.

I recently bought some new micromesh sheets in the 8000 and 12000 grits. Previously I had the basic hobby kit which went up to 6000. The difference in the shine is marked. Polishing up to 12000 grit micromesh means that you can buff to a glass like shine by hand on a tea towel! Add a little mechanical buffing on the dremel and they are glorious! With this one I made the cabochon (hand formed) then I baked and polished it then added the frame and rebaked.  I polished again through the last 3 grades briefly and then buffed. It certainly doesn't look like polymer clay any more!

I also made my first proper pen, with a pen kit rather than covering a cheap biro. Again for my mum, she was a little spoilt I think, but she deserves it!

In theory it's refillable but I had some trouble fitting the parts together so I am not sure how easily it will come apart to put refill in. Again it's polished with the new finer micromesh cloths and it's a thing of purple beauty! I wish I had made my polymer clay bits a tiny bit thinner so it doesn't bulge out from the central band. Next time I will - or I'll just cover the band with a different clay pattern too! I've ordered some more pen kits so watch this space for more. I have ordered some different types to try out. There are so many different ones out there it's hard to know which ones to buy.

I've made some other jewellery bits with the same 2 purple flower canes. As always I didn't make the canes big enough, if I didn't like them I would have lots of it of course! Sometimes canes just really turn out great. With these I love how the colours work together but because I wasn't sure if using all purples would be too much I only made very small canes. Luckily I am getting good at cutting thin so I have made them go a long way.

Latest jewellery - and it's all for me!

I haven't had any new jewellery for myself for a while now, I was busy making sale stock and completing orders. So far this year things have been quieter so finally made myself some new things. Here's some of them

3 blue and white skinny bangles. I am road testing these to see how they strong they are. Baked them extra long to try and make sure they were strong!

Blue and white oval cabochon pendant, I do love this simple blue and white flower cane. This is the second batch of the cane I've made and I can see I will be making more.

The blue and white colours are also the colour palette for this week in the Flickr Colour Palette a Week group - do come and join in with whatever medium you craft in.

Hollow beads made using the technique I learnt on Christine Dumont's Hollow Bead Workshop. She is just about to start an online workshop for these beads so follow the link and check it out.

Hollow beads strung as a necklace


I've more to show you tomorrow. Hope you all have a great weekend
Cara

Choker necklaces and new pendants

Suddenly everywhere I look there are choker necklaces - and they look fab!  I wanted to make some but wasn't sure where to get them in the UK (did have a look on the bead supply websites but didn't find them).

At the London Polymer Clay Group meeting on Sunday, Rebecca Thickbroom  (who is one of the organisers of the Polymer, Pamper, Play event I am very much looking forward to!) showed some beautiful choker necklaces

Rebecca's beautiful choker pendants!

They were inspired by the amazing work of Helen Briel and made using one of her texture stamps

Even the back of Rebecca's pendants are beautiful!

Rebecca was able to tell me where she bought her wire chokers  in the UK and I ordered some.

So I was playing with my rainbow stripe jellyroll cane and planning on making a cabochon pendant with it. I decided to make a round one and use a large cane slice in the middle. I carefully firmed the first slice right in the middle and then looked at it and couldn't see how I could tidily cover the rest without any big black gaps or over lapping the middle slice, which I didn't want to do. And as happens with all the best pieces it just made itself.

 

 I loved the basic concept but was concerned with how I was going to sand it, I only wanted to sand the cane slice and I had smoothed it flush with the black. Also it was bulky - then I had a light bulb moment ;)

This is the first time I have used a light bulb to cure polymer clay in a dome shape, luckily I had put the last one that blew in my clay supplies for just such a moment (as you can see I was getting carried away with my rainbow jellyroll and signature canes)

So here is the end result of the lightweight pendant which drew inspiration from Rebecca's pendants above. I used a very similar textured back which is beautiful, professional looking and best of all doesn't need sanding - genius! Another opportunity to use my signature cane. I just love this, especially strung on the choker wire (so much easier than making up a cord like I normally do!).

I have a small sale in my local church hall (as part of a friends foot pampering night) next week and I shall be making some more along these lines to see if other people like them as much as me!

Phew! Think I am done for now. Thanks for sticking with it.
Cara x

(still not perfect but better photos at least)

Signature Cane

The main demonstration at the London Polymer Clay Group was by on making signature canes Susan Rimmer, thanks Susan it was an interesting demonstration.

 I have been thinking about signing my work and did play about with a stamp made from bent bits of coke can back in the autumn but I wasn't happy with the results, it wasn't obviously a signature and I mainly sanded it out the few times I tried it. Off course the first one I made was back to front because I forgot it was going to be a stamp image and didn't reverse the letters.

So here's the cane I made after Susan showed us how she made a 2011 date cane (wonder if she'll use it?)

Before reduction 4.5 cm across (See that green smear at top - must remember to  clean my blade!)

The smallest is 5mm across (I see I didn't trim the second smallest back to the neat part and they could be more square!)

I thought I would like to incorporate the flower I use on my logo (shown below in case you haven't seen it already)

I was thinking about adding a flower on to the outside of the cane I already had when I was struck by inspiration - why not put it in the loop of the J?  I had kept part of the original cane large (4.5cm across, I got carried away!) so I did some surgery. I didn't want to cut the letters because I was worried about not rejoining accurately so it was a little tricky. I had to make the flower smaller than I would of done as I couldn't get in to trim out the clay easily.

The flower is in pearl but I decided that would help it stand out a little. I quite liked it this size. 

I had noticed that my J lost some of it's curve on the bottom loop on reduction with the previous cane so I thought I might try and encourage it to stay round with a little extra clay - 2 little sausages on the bottom as shown below.

Here it is reduced, my cunning little snakes didn't work, seems obvious now on hindsight what would happen but you've got to make these mistakes - it's learning you know! The little snakes compressed the black line of the J making it look broken. The flower is also quite tiny and the pearl when squished down looks darker.

I want to add a border but am not quite sure what. I wondered about using a zebra cane....

..but I think it's probably too fussy. Might work better thinner maybe? I will have to play about with it a bit. Am I going to use it? Well really I would like to remake another one with a bigger, white flower in the J as I construct it but I have lots of other things on my to do list that are more important. I am preparing for a small sale in just under 2 weeks time so perhaps I will put some on my new stock just to see how they look. I'll let you know.

Name badge

I was lucky enough to be able to go to the London Polymer Clay Group meeting today (thanks to my parents for looking after the children as hubby was busy shock horror!). I decided to make myself a name badge yesterday evening so it was made in a bit of a rush (one day I will learn not to be so chaotic but until then last minute it is....). The photo too was taken in a rush and the lighting is terrible. It is on my list of things to do in Feb to try and sort out some better lighting for both taking photos of my work and for my sale table -hoping it can be the same lights I use for both.

I had a lovely day out in London, 2 hours of peace on the train would be a treat enough but to go and talk polymer clay with nice people who understand, to see so many lovely pieces of work by the talented members of the group and to be shown some new techniques is fantastic. Unfortunately I can't make the next meeting as it is on my youngest daughters 5th birthday but I do have Polymer, Pamper, Play to look forward too in March! A whole weekend of polymer clay!!

I hope you all get time to be creative with friends too.

Pasta Machine Thickness comparison table

Since I started improving my polymer clay work by following tutorials and going to workshops I have found it very confusing when people give you a pasta machine thickness as the different brands (particularly Atlas and Imperia the main 2 quality machines) don't compare easily. I have an Imperia machine which I love, it is easy to take apart to clean, only requiring to remove the end plate on one end (the one without the knob) with 1 screw and then I can push out the rods by hand and clean the scraper plates. I recently acquired a cheap Kitchen Craft pasta machine which looks like an Atlas but it doesn't run smoothly and the clay always wrinkles up on settings 8 and 9 - I would pay the extra and get a quality machine if you can.

I spent a lovely day in London yesterday with the London Polymer Clay Group (it was a blissful 2 hours on the train from me which I thoroughly enjoyed and I managed to squeeze a flying visit in to the jewellery gallery at the V&;A museum too!). I had already made thickness chips for the 2 machines I have and Nina kindly allowed me to make a set on her Atlas so now I have all 3! Here's the measurements

This is what my chips look like

 They will probably be a bit different from machine to machine and possibly even from different sides of a sheet depending on how straight the rollers are but hopefully it's a useful starting point.

So if you want to compare I would say as long as you remember a 1 on an Imperia is about the same as a 2 on an Atlas, 3,4 and 5 are much the same and the thinnest on an Imperia is like a 7 on an Atlas.

(Toni the table won't be visual enough for you - your machine is very close to the atlas measurements)